If you would like to view these pages from within your browser, you should try Adobe's Reader, which incorporates the latest in Browser technology to vastly increase the value of documents published on the Internet.

A 3-component, 100% solids, deep-pour, multi-purpose epoxy grout for fast, permanent alignment of reciprocating equipment. Also used as a polymer concrete for fast reconstruction of worn or damaged foundations. Chockfast® Red provides excellent vibration damping for static and dynamic loads, while its gentle exothermic cure allows for single pours from 2" to 18” (51 mm to 457 mm).

A 3-component, 100% solids, enhanced flow, epoxy grout, Chockfast Red SG is used to grout large machinery applications where a lighter consistency material is required and clearances from 1” to 3 “ (25 mm to 76 mm) are typical.

A 3-component, 100% solids, deep pour, epoxy grout; ESCOWELD® 7505/7530 offers many benefits designed to simplify equipment installation while providing excellent chemical resistance and vibration damping for pumps and other critically aligned rotating equipment. Pours from 2" to 18” (51 mm to 457 mm) are typical. ESCOWELD® is available in North America only.

3-component, 100% solids, high chemical and temperature-resistant, high flow epoxy grout for new or retrofit installations in caustic environments. Chockfast® Blue can also be used as a substitute for steel soleplates or rails; normally used in a thickness range of 1” to 1 1/2” (25 mm to 38 mm).

2-component, low viscosity, structural epoxy “chock”, or “poured shim” with variable hardener ratios options. Replaces tediously fitted steel chocks or shims. Assures intimate contact with machined or un-machined equipment bedplates. Virtually 100% effective bearing underneath supported equipment. Normally poured in thickness’ of 1-1/4” to 2-1/2” (32 mm to 64 mm).

2-component; filled structural epoxy “chock” or “poured shim”; used to support and maintain permanent frame alignment under hot-running machinery. Elevates equipment, allowing a vent space between equipment and foundation to lower foundation temperatures and minimize upward thermal growth. Virtually 100% effective bearing underneath supported equipment. Normally poured in thicknesses of 1-1/4” to 2-1/2” (32 mm to 64 mm).

2-component, highly flowable, thin pour “chock” or “poured shim”; designed to maintain proper alignment and support of machinery and equipment. Able to withstand severe industrial environments with a high degree of both physical and thermal shock resistance. Normally poured in thicknesses of 1/2” to 1” (13 mm to 25 mm).

2-component, high-strength, fast-setting, multi-purpose epoxy with a convenient mixing ratio of 1:1. Can be used as a liquid shim, an anchoring adhesive or as structural gap filler. Sets within 15 minutes, with full cure in 6 hours. Hardens to 78 Shore D in 30 minutes and 84 Shore D in 4 hours. Normally poured in thickness’ up to ¾”. (19 mm).

A precision, non-shrink, cement grout that meets or exceeds all requirements of the Corps of Engineers CRD C-621 and ASTM C-1107.

2-component, epoxy resin formulation intended as a flexible foundation seam sealant. Self-leveling; flows smoothly; good adhesive strength and flexibility over a wide temperature range. Used to seal joints where expansion and contraction movement will take place. Remains flexible over a wide temperature range, 0°F to 150°F (-18°C to 65°C). Durable and weather resistant. Vibration and impact resistant.

2-component, 100% solids, epoxy paste developed specifically for filling, smoothing and fairing applications on metals, plastics (FRP), wood or masonry. Smooth consistency and excellent non-sagging properties. Excellent resistance to fresh water, salt water, crude and refined oils, gasoline, jet fuel. Provides a tough, uniform surface that will readily accept any top coating or lining. The cured epoxy is readily sanded or ground. The excellent feathering properties facilitate achieving a precision surface profile or smoothness. Contains no metallic fillers.

A specially formulated epoxy adhesive resin system designed for pressure injection repairs to concrete and adhesion of new concrete to old concrete.

2-component, lead and chromate free, rust inhibitive epoxy primer specifically designed for use in conjunction with ITW Polymer Technologies products applied to metal substrates. Recommended for use as a metal primer in severe industrial and chemical environments. Possesses excellent adhesion to properly prepared iron and steel surfaces, providing rust resistance to ferrous substrates, both on initial application and in the event of damage to the topcoat. Can be used under many epoxy, urethane, vinyl, chlorinated rubber and coal tar/epoxy finish coats.

The latest in high technology, high bond strength repair systems. Use to join such dissimilar metals as iron, steel, aluminum, tungsten carbide, brass, zinc, and zinc alloys without the problems of galvanic corrosion. Adheres tenaciously to properly prepared surfaces. Hardens to a rigid metallic mass which permits drilling, tapping, or machining with ordinary metalworking tools. Maintains an integral bond, a high level of resistance to impact, abrasion, chemicals and high temperature.

A smooth ceramic-filled epoxy putty with exceptional wear resistance. The "noslump" nature makes it ideal for repairing overhead, vertical or curved surfaces. Well suited for the repair of severe service equipment commonly found in a variety of industrial and marine applications.

A unique ceramic filled, high build, brush able epoxy coating. Formulated for unequaled chemical and corrosion resistance with outstanding wear properties in adverse environments. Ideally suited for lining and resurfacing all types of severe service equipment commonly found in a variety of industrial and marine applications.

2-component, high strength epoxy paste for the repair of punctures or cracks in tanks, pumps, pipes, steam lines, sea chests, valve bodies, and many other applications. The material is also used to fill holes, voids and to provide a smooth surface for repairs at temperatures up to 428°F (220°C). Resistant to most acids, alkali and hydrocarbons and will adhere to clean surfaces such as steel, cast iron, bronze, aluminum, copper, nickel, wood and most plastics.

2-component, fast-setting epoxy laminating resin system designed for high strength fiberglass reinforced repairs to pipes, tanks, valves, and other equipment subject to corrosion or erosion. Used to repair leaks in areas at operating temperatures to 428°F (220°C). Excellent resistance to salt water, crude and refined oil, gasoline, caustics and most acids.

An aromatic hydrocarbon solvent used for general epoxy cleanup of tools and equipment used for mixing and applying epoxy materials. It must be used before the epoxy has set. Also used for removing grease, oil and other contaminants from surfaces prior to applying epoxy materials.

Release Agent prevents adhesion between most ITW Polymer Technologies' products and surfaces of metal, glass, rubber and many plastics. Used where the minimum possible clearance between resin and mating surface is required.